Diy Washer Dryer Pedestal Dimensions

Because my washer and dryer seem to be deeper than yours (i needed at least 33 depth, so i went with 3'), that also worked out well in getting the most out of the boards. Depending on how high you want the washer dryer to be, you will need to get the corresponding sizes of lumber.

Visit the webpage to read more on standard washing

Save your money—you can build your own bases from standard lumber.

Diy washer dryer pedestal dimensions. It's well worth it, and looks great, if you have a little time on your hands. To start, measure the length and width of your washer and dryer. You purchase this washer and dryer as one piece.

To start, measure the length and width of your washer and dryer. With the pocket hole jig set for 3/4″ material, drill pocket holes in each end of the framing pieces as well as all four edges of the side panels. I also wanted the storage space underneath for laundry baskets and such.

You only need to do this step if you need your pedestal pushed all the way back as far as possible to the wall. Measure your washer and dryer for the height, width, and depth of the machines. Also note the size under the bases can be adjusted for laundry basket.

Build your own washer and dryer pedestal bases to bring your laundry up in height. In order to do this, you will need to measure the center to center dimensions of the feet on the washer and dryer. Cut the piece for the upper shelf.

If you want, leave the wooden surface as it is, but don’t forget to sand it down to remove any rough surfaces and edges. That's your minimum size for the pedestals. The platform ended up being 60in by 31in and 15.25in tall.

The free plans to build a pedestal for a washer and dryer can be finished any way you. Diy washer pedestal | laundry pedestal, washer pedestal, laundry room diy. Spiffy (aka micahstubz ), yes the man that builds websites, makes videos, is a great dad and a computer genius… he saw a few diy washer/dryer pedestals on pinterest and decided it was the perfect project to make the most of our small laundry room.

I didn’t make any modifications to the plans. I have looked at many different diy pedestals but once i saw yours i knew it was the one….my question is the top of it….it looks like you put the decorative molding around the edge of the top so that it is flush with the piece of plywood you put on for the top…yet in the after picture it looks like there is another board on top of that. The dimensions of this particular pedestal are 54 l x 26 w x 17 1/4 h.

Here is a pretty simple explanation: Bottom shelf and top shelf. It should be easy if you can cut some wood straight and hammer nails into it without hitting your fingers.

You can make them longer and wider if you want the extra space to stand on to reach overhead shelving or to set the laundry baskets on. I will share my sadly neglected laundry room pics with you in my reveal because today it’s all about the pedestal! In that case, here’s a quick guide to diying your washer dryer pedestal.

Diy laundry pedestal plans with drawers These holes need to be as exact as possible for the feet to sit down in them. Measure your laundry machines and adjust to fit.

A single unit washer and dryer, also known as a unitized washer and dryer, is an appliance that is “stacked” and connected into one unit. I had to use these dimensions because the space where my washer/dryer is very small. As you can easily notice in the plans, we recommend you to cut the 2×4 slats at the right size and to lock them together with 2 1/2″ galvanized screws.

We used these dimensions since it would hold our washer and dryer, left room for the cabinets we wanted, and had enough room underneath to store the laundry basket. 3/4″ plywood for top shelf & 1/2″ plywood for bottom shelf. Or you can make one long pedestal to fit under both the washer and the dryer.

Check if the corners are right angled by using a carpentry square. First you need to measure t. This is an optional step but the bottom shelf of the pedestal had a cutout for the ventilation on the dryer.

Cut the pieces for the legs, the side framing, and the side panels. Special thanks to sausha for letting us create this tutorial from her laundry room bases. The first step of the woodworking project is to build the base of the washer dryer pedestal.

Washer and dryer pedestal. For the Home Pinterest