Diy Cornice Board Foam

This thing is so lightweight, it doesn’t take much to hang it. Marty added the measurements we wanted to the boards, used a straight edge to draw the cut lines, then cut with a jigsaw.

How to Make a NoSew Cornice Board Cornice boards diy

Figure out the width that you want the cornice to be.

Diy cornice board foam. Make a mark just below the edge of the curtain rod edge. Fold batting over and staple to the back of cornice board. To make your own diy cornice window treatment you will need:

Cornice boards are cheap to make. Custom cornice for less than $30. Material (1 yard) enough foam core board for your project (i used 2 30x20 boards from walmart for $10) coordinating trim (enough to go along the edges of your project) krylon easy tack.

Hot glued a ring onto the back top corner of the board on either side. Custom cornice for less than $30: I bought just one window panel to match my comforter.

Deco wrap is the original patented no sew cornice as seen on tv and qvc and sold at walmart, joann fabrics, hobby lobby, hancock fabrics and independent fabric stores but is now exclusively available on this site direct from the inventor, allowing us to be the most affordable foam cornice board on the market. Fold and staple batting along the top edge. And that’s how to make a cornice board out of foamcore.

Creating a cornice for your window can be as simple or elaborate as you would like. Place the foam board you just cut on a flat surface and put your curtain rod on top with the brackets facing up. Be sure your boards are in square!

I recently did a diy overhaul on my master bathroom, and i wanted to create a cornice window treatment for the window. Cut your styrofoam panels the length and width of the cornice board. Custom cornice for less than $30.

Cut a piece of foam board to the width of the window plus 6 inches. I hope this inspires you to try this project. With deco wrap there is no sewing.just wrap, tuck, hang.

Determine the height of the cornice and cut the foam board accordingly. Continue pinning your fabric around your board pulling your fabric tight as you go. Next grab a remnant piece of foam board and place perpendicular on the short side.

There are lots of variables thrown into this calculation, so your exact cost may vary quite a bit from mine depending on your materials (how expensive the fabric you choose is, and what type of wood you use, etc). I cut a strip the length i wanted plus 4 inches and the width i needed plus 2 inches. This is a very light weight cornice that is strong and easy to mount.

Then cut two smaller pieces for either side. (while doing this take care that the batting was pulled at a consistent tension so it laid smooth on the front face.) 5. I laid the panel on muslin for a liner and sewed all 4 sides leaving an opening to turn inside out.

Foam board wood styrofoam step 2: Insulation foam board (if you can find 1.5″ thick like this one, this would be even easier. So, i took on the project anyhow and decided to…

I used an exacto knife and it cut like butter. Move to each side and repeat this step. Cut and attach fabric glue staples duct tape.

This cornice is 11 inches high. Pulling your fabric tight, pin the bottom edge of the fabric across from the top pin next. This is a very light weight cornice that is strong and easy to mount.

I found lots of great tutorials on creating one out of foam board, but couldn't find a single tutorial for a corner window. The total cost of this project was $28.97, and we almost have enough fabric and batting to make a second cornices. Our side pieces are 4″ x 17″ (4″ is the depth we wanted the board and 17″ is the length).

Time to glue up all of the pieces. The 12 drop height avalon cornice kit works great in most rooms and with all ceiling heights. The total cost of this project was $28.97, and we almost have enough fabric and batting to make a second cornices.

Fold, trim, and staple sides and corners of. This is the length your cornice will be, including the side pieces (at 6 inches for each side). Cut out the length and width of foam board.

I made my cornice to go on 2 simple curtain rods with 3 inch returns. Just 2 small nails will do it. A good, sharp utility knife.

Custom cornice for less than $30: Buy the appropriate amount of foam board you will need (i found mine at the dollar tree and needed 5).

Cornice Board made out of Project Foam Board Covered in