Diy Cork Coasters Mod Podge

Paint a coat of mod podge over the top of the paper. Apply at least two more layers of mod podge.

mod podge coasters1 coasters Mod Podge Outdoor Scrapbook

Moreover, it is way stronger than regular glue which means the diy products.

Diy cork coasters mod podge. Add two more coats of mod podge letting each coat dry between applications. These custom coasters are also easy to make. Place the paper down and smooth.

That you'd like on the finished coasters. Add a layer of mod podge to the top of a tile; Let them dry about 15 minutes between coats and make sure you hit the edges.

Apply mod podge to the coaster and then stick the felt to the coaster. Add another coat of mod podge and repeat 2 more times. Once the coasters are dry, trim any excess paper around the edges with the craft knife or scissors.

Using the stamps, stamp out the names/date/etc. Step 3…mod podge the top… once they are all glued down, apply at least 2 more coats of mod podge to the tops of the coasters. Cut your maps to fit your tiles.

First, i painted a coat of mod podge on the top of the tile. Flip the glass upside down on top of the cork and trace the circular mouth of the glass with the pen. And here’s how to do it!

Mod podge is a superior version of craft glue. I like to have just the tiniest amount of “border” on the edges of my coasters, but you don’t have to. Apply mod podge to the back of the six pack and then stick to the other side of the coaster.

Using a brush, apply mod podge/glue to a square of cork. This’ll seal and harden them up and protect them from any moisture. Add a medium layer of mod podge to the coaster and then lay the paper down and smooth.

Some cork or felt dots sealer (optional as i normally use mod podge) sanding block or sand paper. Next, i turned the tile back over and painted on. Repeat until you have the number of coasters you want.

Cool diy cork photo coasters we’ve already told you how to make tile photo coasters , and today we’ll realize the same idea on cork. It’s easier to have it to hand as it can be quite fiddly to separate the layers. It's a good idea to add four cork circles in each corner on the bottom of the coasters to prevent scratching

Here is what it looks like when the mod podge goes on, but don’t worry, it dries clear. Repeat with the additional tiles. Let dry and give another coat.

After that dries, add a layer of mod podge to the tile itself and adhere your map to it. Let dry for several hours. Let cure for 28 days before placing hot drinks on.

This will keep the paper from wrinkling when it’s applied to the tile. It dries clear, but will leave some brush marks depending on your application. The first coat of poly looked great, but the moment the second coat was applied 4 days later the finish looked like it was hit with stripper instead of a clear coat.

Glue cork backs onto the coasters. The mod podge is a process but not too bad: One time a day for 3 days, add a coat of mod podge onto the coaster, waiting a full 24 hours between each coat.

Then affix photo to cork. By which time the mod podge has partially dried up. Repeat for each photo and let dry.

The outdoor mod podge is best for this as it will hold up better. It acts as a glue as well as a sealer. Then place the paper on top.

Start by applying a thin layer of mod podge to the back of your map paper. At first the coaster will have a bit of film on it, but the mod podge dries clear. Mine curled up a little (cork if flexible!) but they flattened out on their own.

Lift up the glass and set it back down on a new space of cork. Before you start with the mod podge, take your serviette and prepare it for your tile. Then spray 2 or 3 coats of acrylic sealer on top.

After that dries, apply about 3 layers of mod podge to the top of your coasters allowing them to fully dry between each coat. You need ceramic tiles, mod podge, acrylic sealer, a sponge brush, paper and cork backing or felt. Then, i smoothed some scrapbook paper over the mod podge.

If you have an image you want to add, put mod podge on its back so that there’s enough coating to stick it to the coaster. Hi amanda, my wife put 6 coasters together with modern comic book page pics, 5 layers of mod podge, wet sanded with 1200 grit, and coated them with a polyurethane. Keep smoothing until all of the bubbles are removed.

Coat the top of each tile with a thin layer of mod podge. Let the solution dry for about 15 seconds or so, then put it on the coaster where you want it. Wait another 20 minutes so that the mod podge can completely dry.

That way, your coaster won’t stay sticky. Do one at a time…it dries quickly! Let the mod podge dry completely.

EASY DIY Coasters You Can Make in Minutes! Coaster

Diy horseshoe coasters What you need Cork board