Diy Dust Collector Impeller

I bought a stock harbor freight 2hp dust collector and converted it to a 2 stage cyclone separator using a piece of 24 gauge sheet metal that i had cut a local machine shop for $50, some scrap wood and a $20 55 gal barrel. Designing and making wooden blower fans.

Larger Impeller for Harbor Freight Dust Collector

This time bigger and stronger.this first video of it covers the mounting flange and the impeller.

Diy dust collector impeller. The dust collector build started with a stock 2hp single phase harbor freight dust collector. Diy and crafts • woodworking •. It was backordered and took a while to get to delivered.

The total cost was around $550 if i include the cost of the ddxl. Upgrading a harbor freight dust collector. The picture at the side shows the blower components:

It is a typical thien baffle with a slot cut three quarters of the way around to let the dust drop through to the collection bin: It's a lot of pressure for a dust collector type blower, but a vacuum cleaner or a shopvac will typically develop about 150 cm of suction if airflow is blocked, about four times as much. Wendel built a small dust collector with a tile saw motor, i knew my old motor had found its destiny.

I removed the impeller using a puller tool. Single stage means the dust is sucked through the impeller (fan) and dumped into the lower bag. A while back i bought a leaky air compressor for $50 because it had a good 3hp motor on it that i figured i could use someday for something, probably.

The impeller is from a rikon dust collector. Diy dust collector impeller very cheap to build as it only requires your existing shop vac hose, one more hos… a diy dust collector will help you avoid slipping. Heavy wood chips fall into the waste drum, while fine dust particles are drawn up through the impeller into the filter canisters (this is.

The dust collector has 3 main components: Posted on april 11, 2014 by garagesandals. Most shop vacs actually consume more power, and are louder than larger dust collection units like the one in the background of this photo.

Building a big dust collector blower #1 as my old blower destroyed itself i had to make a new one. Shop vacs make convenient mobile dust collectors, but they are very loud and consume so much power that you often have to run them on a separate circuit. The stock blower can’t push enough air to support a 6″ opening.

How to make a wooden impeller. The upper bag collects fine sawdust and lets the exhaust air back into the shop. Diy diy dust collector dust collector homemade dust collector woodworking

To seamlessly connect to the super dust deputy xl i’m going to upgrade the impeller. To attach it, more construction adhesive is applied to the rim of the centre section. Turning tools wood turning dust collector coasters woodworking projects how to make fans future.

Any dust particles that do not get caught in the filter drops into the blue bucket. The next part goes at the bottom of the centre section and divides it from the collection bin below. Diy wood projects projects to try wooden brackets best glue spiral shape dust collector wood dust shop plans i work out.

In testing,we found the more you load your collector, the greater the benefit. Article by juan guillermo roldan peña. The impeller, which is connected to the motor that sits on top of the collector creates a cyclonic force that causes air (fine dust and wood chips) to spin around in the cone.

Diy and crafts • woodworking •. From the research it has the same shaft diameter as the harbor freight one and is a direct bolt in. Below is the cost breakdown of the dust collector build:

The motor with the bushing attached to the arbor, the impeller with the two threaded holes in the flange to accept set screws to tighten against the bushing, the motor mounting board with the rabbeted hole that accepts the motor arbor (this rabbet received a bead of caulk when the motor was attached to seal that connection), and the piece of ½” angle iron. Enough to float the head of a wooden mallet about 45 cm above the outlet. The stream of air coming out of it is also quite powerful.

Pin on WoodWorking