Diy Dust Collector For Miter Saw

Miter saw dust collection is tricky because it spews sawdust in every direction, making it hard to contain. Since then, i've been brainstorming the best way to hook up that beast to all my machines.

Pin on Woodworking Jigs and Accessories

Also look at the overall depth required for your saw.

Diy dust collector for miter saw. This dust hood helps corral the mess by giving it somewhere to go—into a dust collector or shop vacuum. It makes it very easy to use, small and it has a clamp ring and also a chain system. A miter saw is one of the handiest tools you can own, and one of the messiest.

Use the clamps to secure them together. The system has a stock harbor freight dust collector that i modified to become a cyclone separator into an old 55 gallon barrel. Take out the dust funnel and position the tent over the hole.

Connecting your miter saw to dust collection. To do that, swing the saw to full miter capacity in each direction, and measure the overall width. If that’s more than 31, you’ll need to make your hood wider.

After building the down draft base, i assembled the sides and top of the box cutting out around the features of the saw to create a custom fit box that was decently dust tight. At the other end is. This dust collector is made from nylon, and it comes with interior baffles with no assembly required.

I’ve always found the working height to be a bit too low, so this will make it more comfortable to use. Compound miter saw dust collector hood. I use a shop vac right now, may move to a dedicated dust collector in the future.

Diy dust collection system miter saw. Having the saw on the floor or a makeshift sawhorse table means more fiddling with support blocks, interruptions in workflow, and not quite square cuts. To install the frame, i made a couple of hardwood mounting brackets that tilt the frame back 20°, and attached them to the bottom of the frame.

Press the dust funnel into the hole over the tent fabric, and attach it to the platform with screws and washers. How to make a miter saw dust bag: The collector is made from 1/2 maple cabinet grade plywood and a 4.

A month or so ago i built a miter saw station from plans from www.woodsmith.com. The chips and sawdust it creates get everywhere. Of all the tools connected to my dust management system, my miter saw is the most likely to be relocated.

It comes with a chain system and makes from high quality. I threaded the extra hose i purchased through the hole, and hooked it up to my miter saw using a bosch 35 mm adapter. You can either get the measurement from your owner’s manual, or just pick a tube yourself.

You can build a hood for your saw from plywood and a few fittings. But right now my worst offender seems to be my miter saw. From the front edge of the bottom to the back of the hood, there’s almost 40 of depth, so that probably won’t be an issue.

The first thing you’ll want is a piece of plastic tubing that’s large enough to fit the dust vent on the back of your miter saw. I chose this diy miter saw station as the first project for the new shop because having a way to make quick, accurate, repeatable miter cuts makes every other project so much easier. To keep the miter functionality of the saw and remain able to produce angled cuts, i designed two removable wings and a folding top that finish off the box.

Check out the video below of how i built this dust hood along with some footage of it in action. Underneath the workbench, i connected the hoses to the dust cyclone: It's a great saw but the dust collection is awful.

No comments 7 genius ways to improve miter saw dust collection the handyman s daughter pin on work ideas a simple mobile solution how make compound hood mitre for saws fine homebuilding bosch axial glide upgrades mods dan pattison chris billman hoods woodworking removable by patmfitz. Miter saws make a lot of dust, but this dust hood can keep it under control. Use scissors to cut an x from corner to corner.

It's a bosch 10 single bevel slider that i've had for 13 years. Assemble the diy cyclone dust collector by placing the modified bucket on top of the intact one. I use the miter saw stand by fix this build that.

Last week, i showed you my dust collector setup and how i upgraded it for better performance. Connect the shop vac to the top of the cyclone, and then connect the other. Attach a 4 dust collection hose to the underside of the dust funnel.

For that reason i used key hose clamps (instead of cheaper screw hose clamps) to attach the 4″ flexible hose. Been trying to take dust collect in my small shop more seriously. We recommend some excellent miter saw dust collector bag below:

You can download his plans for $9, and they are worth every penny. This dust hood still retains all of its good features like the hinged panels above the saw as well as the downdraft box in the rear. By admin filed under diy;

With the dust collector out of the way, i was able to move the miter saw station a bit further down the wall, and raise it up about 4″ higher. Ryobi miter saw dust bag: The station is great and i’ve used it for several projects but the only problem with it is it has no dust collection so i set out to remedy that situation.

Kapex Workstation Woodworking workbench, Woodworking