Diy Pocket Door Cabinet

Then use a pocket hole drill bit and set it to the right wood thickness. Add 1.5” pocket holes down one side of 3 of the boards.

DIY pocket hole Door, DIY door hole

Add a bit of wood glue to the edge of the rail, then secure it to the edge of the stiles.

Diy pocket door cabinet. Paint the cabinet door and distress. Attach the top to the cabinet with 3.5” wood or spax screws through the face frame and into the top. Drill pocket holes in the side edges of each piece.

Attach to cabinet using wood glue and 1 1/4″ pocket hole screws. Pocket cabinet doors use a series of 4 tracks that the doors slide on. Decoupage the book paper in the inset.

Then, line them up flush and attach them using 2.5” pocket hole screws. Then she sanded down the edges and corners to give it a distressed look. Long and exactly 1 in.

The height is 34 1/2″ tall. The cabinet material is 3/4″ thick. Center it on the cabinet and attach it with pocket hole screws through the vertical sides and center divider.

Then, build the new header using your. Using a drill, make shallow pilot holes at the front, middle and back of the drawer slide. Kv 72 inch shaft for 8092 pocket door sold per pair by knape and vogt.

Bore pocket holes on the end drawer pieces (q) as shown and screw the box together. My doors were 6mm laminated glass taken from another cabinet, but if you want to have some made, simply measure the width of the opening, divide by 2 and. The measurements in this plan will leave a 1/8” spacing around the door.

Using wood glue and 1 1/4″ pocket hole screws, attach both the rails to one of the stiles so that the groove in the center lines up and the top/bottom of the stiles are flush with the outer edge of the rails. Now it is time to assemble the cabinet doors! Attach the top to the cabinet with 3.5” wood or spax screws through the face frame and into the top.

Attach the drawer slide using the screws provided. Narrower than the drawer opening in the face frame. The diy furniture plans to build a stackable cabinet feature sliding doors with glass or plexiglas inserts, and a shelf behind them.

Note that the center door cabinet shelf is slightly wider than the drawer cabinet shelves. Depending on the pocket door hardware you may need to place them away from the cabinet sides. Cut the pieces for the shelves.

Then, line them up flush and attach them using 2.5” pocket hole screws. The point of this is to hide your hardware! If you purchased pocket hardware and a new door, you don't have to worry about saving the door.

Hold the drawer slide firmly against the underside of the spacer block, and flush with the front edge of the cabinet. Cut 1×6 boards to form a box that is 13 in. Making sure that each door sat into its own channel.

Add 1.5” pocket holes down one side of 3 of the boards. Drill 2 pocket holes set for 3/4″ thick material in each end of the cabinet door rails. Assemble both door frames with glue and pocket hole screws.

Add supports for the large cabinet shelf from 3/4″ plywood. Use a framing square to square up the drawer. How to build a cabinet using pocket hole screws.

Adjust your dimensions as needed. Attach your 1/4” plywood panel for the back with glue and brad nails. Place the bottom tracks first and then the top tracks.

The final dimensions of this cabinet after the back and face frame are attached will be 24″ but the sides, bottom and shelves are 23″ deep. Now, it's time to begin installing the pocket door, starting with your header. Add 2 pocket holes set for 3/4″ thick material with a pocket hole jig to each side of the rails on the back of the boards.

Cover the inset of the cabint with modge podge and press the book paper inside, paying particular attention to. Clamp your jig to your wood with a c clamp so it doesn’t move… then use the hole in the jig as your guide, and drill two pocket holes per side of the small pieces of wood for the doors, and one per side for the drawers. On december 11, 2015 • by kristi linauer • 67 i can now check off a third major project from my music room “things to do” list because i’ve finally finished the pocket door bookcases!

The toe kick is 3″ deep by 4″ tall cut out of the sides with a jigsaw. Read the assembly instructions carefully to determine the new header size. Julie adds color to this cabinet door with two coats of chalk paint.

Sliding Barn Door w Hardware by RusticaINNOVATIONS on Etsy