Diy Wood Mantel Cover

These will be the side / end pieces. To secure the diy wood beam mantel to the wall, we needed to screw in a few wood cleats.

Pin on Main living areas

This rustic fireplace mantel has the charm of reclaimed wood but is inexpensive and easy to make.

Diy wood mantel cover. This allows seams to be hidden from the front. Wood beam mantel diy steps. The mantel is removed, the cleat is attached and now we’re ready to actually build the faux wood beam mantel.

Two pieces of wood veneer. Using 2×4 wood pieces cut the pieces needed to create the faux brick corbels. Then i drilled the pocket holes.

We wanted a more rustic feel so we didn’t use it. Build a diy faux beam fireplace mantel cover jennifer rizzo. We cut a 1x6 to size and nailed it to the front of the mantel.

Cut face board length of mantel plus an additional 1.5”. (2) pieces of lumber @ 1″ x 8″ x___ the depth of your mantel to the wall. Since our new mantel was slightly larger than the previous mantle, we built the mantel out with mdf sheet, cut to cover the existing drywall mantel.

Materials for fireplace cover diy. Cut the top board the length of the mantel. Wiped it free of dust and.

So my little partner, noah and i used hammers, screw drivers and chains to mark and scar the wood. *these materials and instructions are for a mantel that measures 8″ x 8″ x 68″ wide. You can use a stainable wood filler to cover the nail holes and at the seams.

Diy faux barn beam mantel the homemade abode. Next we measured the front portion of the mantel. As for installation, we simply slid the wood “sleeve” over the existing mantel.

My first step was getting the correct measurements. Then with some wood glue and more nails, we attached a second piece of 1×8 cut to the same length. 2 sets at 7in., 5in., 3in., & in.

I really wanted my diy wood mantel to have the appearance of a distressed wood beam. You’ll need to make adjustments if your mantel needs to be wider or narrower. Use a level to make sure the mantel is level before screwing in place.

See more ideas about diy fireplace, diy fireplace mantel, fireplace. How to build a box beam mantel easy diy wood mantel remington avenue faux wood beam mantel sunny side easy diy wood mantel remington avenue how to build a rustic faux beam mantel. Sand, distress, and stain your diy mantel.

One pieces of 1″ x 8″ lumber, 12 feet long. Rustic fireplace mantels diy mantel wood mantels reclaimed wood fireplace faux mantle wooden mantle painted brick fireplaces fireplace modern mantle ideas. Cut side pieces to fit mantel width plus.75″ height so that only one seam can be seen from side.

Using 3/4″ plywood, cut your top and bottom boards to the length and width of your cleat you built and attached above…. The board above is my top board of my faux wood beam mantel. One piece of 1″ x 8″ lumber, 8 feet in length.

This board will not be seen. Cut down a third piece the same length that will have a shorter width to tuck beneath the mantel. We slid the mantel onto the cleats and drilled in a few screws through the top of the mantel, into the cleats.

Attach mdf pieces together with screws and attach to the studs with screws. 1″ x 1″ inch strips of wood; Measure the area the mantel will cover.

Finish nails / wood screws; Total time 2 hours 1 minute. The new mantel top board was cut slightly smaller (the depth of the boards) so the side pieces could be inset in the faux mantel cover.

Using scrap wood plywood i cut out the board for the bottom of the mantel beam. Diy fireplace surround with wooden mantel. You’ll need to make adjustments according to the measurements of your own mantel.

To create the mantel shelf, we nailed an 1×8 cut to length on top of the breastplate and legs. If you don’t have a solid header then make sure you are securing them into the wall studs. How to build a rustic faux beam mantel toolbox divas.

Let the coat of stain dry for at least an hour and then you’re ready to apply a protective finish. To make it look like one chunky piece of wood, we attached a 1×2 to the edge. If you chose to apply wood filler, sand using 150 grit then proceed with 250 grit sandpaper.

We then sanded it down until it was smooth. It fits snugly and so there’s no need for added fasteners. Create diy wood mantel cover yellow the faux brick corbels.

This is such an easy way to add rustic farmhouse charm to an old fireplace or a faux fireplace mantel. Using this diy mantel tutorial you can learn how to make your own wood mantel cover from open shelving, it's easy and full of character. We measured the small rectangle area between where the two boards joined and cut the pieces to size.

Using wood filler, we filled the holes and cracks joining each piece together. Learn how to create your own diy birch wood fireplace cover for a faux wood fireplace insert. *these materials and instructions are for a mantel that measures 8″ x 8″ x 6′ wide.

They were screwed into a header behind the wall. All of the sides are cut in straight edges. If you buy a longer board, it’s easiest to cut them off of that so they match in thickness.

Learn how to build a simple diy fireplace mantel.

Build a DIY Faux Beam Fireplace Mantel Cover Faux beams